+MyADSL 0 Publicado 5 de Febrero del 2004 Share Publicado 5 de Febrero del 2004 Por fin lo he conseguido pero vemos que no es linux ni nada que se le parezca, es un S.O. propietario La velocidad es 115200 8 N 1 y hay que colocar un coversor TTL<->RS232. TX pin 5 / GND pin 9 Por el momento solo he conseguido recibir pero no enviar. He parcheado el volcado eliminando toda la información privada y he marcado con <:::: algunas lineas. Bueno paso a pegarlo ya me contareis. =============================================================== [sYSTEM CONFIGURATION SPECIAL] =============================================================== * System Configuration Register [sYSCFG] : [0x00000100] * Product Code and Rev No. [PDCODE] : [0x251000A0] * Peri Cloclk Disable Register [PCLKDIS] : [0x00000000] * Clock Status Register [CLKST] : [0xC0133166] * AHB Bus Master Fixed Priority Reg [HPRIF] : [0x76543210] * AHB Bus Master Round-Robin Pri.Reg [HPRIR] : [0x00000000] * Core PLL Configuration Register [CPLL] : [0x0001015C] * System PLL Configuration Register [sPLL] : [0x00010148] * USB PLL Configuration Register [uPLL] : [0x000203B8] * PHY PLL Configuration Register [PPLL] : [0x00030248] =============================================================== [CP15 Register Map ] =============================================================== * CP15 : C0 ID Code : [0x41029402] * CP15 : C0 Cache Type : [0x0F0F10F1] * CP15 : C1 Control Register : [0xC000107D] * CP15 : C2 Data Cacheable Register : [0x00000022] * CP15 : C2 Inst Cacheable Register : [0x00000022] * CP15 : C3 Data Bufferable Register : [0x000000FE] * CP15 : C5 Data Access Permission Register : [0x00000FFF] * CP15 : C5 Inst Access Permission Register : [0x00000FFF] =============================================================== * CP15 : C6 Data Region0 Base/Size Register : [0x0000003F] * CP15 : C6 Data Region1 Base/Size Register : [0x00000031] * CP15 : C6 Data Region2 Base/Size Register : [0x0080002D] * CP15 : C6 Data Region3 Base/Size Register : [0x80000025] * CP15 : C6 Data Region4 Base/Size Register : [0x81000029] * CP15 : C6 Data Region5 Base/Size Register : [0x84000027] * CP15 : C6 Data Region6 Base/Size Register : [0x00000008] * CP15 : C6 Data Region7 Base/Size Register : [0x00000008] =============================================================== * CP15 : C6 Inst Region0 Base/Size Register : [0x0000003F] * CP15 : C6 Inst Region1 Base/Size Register : [0x00000031] * CP15 : C6 Inst Region2 Base/Size Register : [0x0080002D] * CP15 : C6 Inst Region3 Base/Size Register : [0x80000025] * CP15 : C6 Inst Region4 Base/Size Register : [0x81000029] * CP15 : C6 Inst Region5 Base/Size Register : [0x84000027] * CP15 : C6 Inst Region6 Base/Size Register : [0x00000008] * CP15 : C6 Inst Region7 Base/Size Register : [0x00000008] =============================================================== =========================================================== 54ADSL Router BRN Loader V1.3d build Sep 04 2003 17:37:25 Broad Net Technology, INC. =========================================================== read(0)= 28 read(2)=59904 AMD Am29LV160DB bottom boot 16-bit mode found Copying boot params.....DONE Press any key to enter command mode ... Flash Checking .. Passed. Unzipping program from bank 2...done Try to find image for running... Unzipping program from bank 3...doneFlush I and D cache ATEXIT : f5454 System Hardware startup ... [GPIO INIT] Initialize Chip Select Pin Setting .. [ADSL] ChipSelect_init() B2CON = 8214E488H [ADSL] ChipSelect_init() : Enable nReady .. [ADSL] ChipSelect_init() B2CON = 4200E488H (_S3C2510) GPIO_init(): Set GPIO for Wireless LED and reset button !! IOPMOD1 f003bf70 IOPDATA1 = 4fffffee IOPDATA1 = 4fffffee === PCI BUS begin .... [PCI FLOW] PCI_2510_Init() Begin .. [PCI IRQ] PCI_2510_Init() Set nPCI_PCCARD=15 , ISR_PCI() [iSR INIT] PCI_2510_Init() Set nPCI_PCCARD=15 , ISR_PCI() [sSMAC] init handler table, handler= 7CC54H [sSMAC] SysSetInterrupt: vector 15 handler 85F64H [iSR INIT] PCI_2510_Initialize(): &INTMASK = F0140008H , INTMASK = 3FFFFFFFH [iSR INIT] PCI_2510_Initialize(): Enable PCCARD_INT=9 .. [iSR INIT] PCI_2510_Initialize(): &INTMASK = F0140008H , INTMASK = 3FFFFFFFH [iSR INIT] PCI_2510_Initialize(): init handler ISR_PCI_Timer5_NormalOn() [iSR INIT] nTIMER5 = 34 [sSMAC] SysSetInterrupt: vector 34 handler 85F34H [iSR INIT] GLOBAL_INT = 31 [iSR INIT] PCI_2510_Initialize(): &EXTMASK = F014000CH , EXTMASK = 8000003FH ---PCI_PCICON_View------------------------------------- [0]Host Mode, [1]Internal Arbitor, [4]ATS, [5]Split Response, [7]Mem Cycle Prefetchable, [8]Config. Done, [9]System Read Ready, [31]Internal Interrupt Signaled, ---------------------------------------------------- [PCI] device(slot)= 0 memory virtual 00000000H , physical 02000000H [PCI] PCI 02000008H [PCI] device(slot)= 0 memory virtual 00000000H , physical 01FFDE00H [PCI] PCI 01FFDE08H [PCI] device(slot)= 0 I/O virtual DC0FFF00H , physical 000FFF00H [PCI] PCI 000FFF01H [PCI] device(slot)= 4 memory virtual C1FFE000H , physical 01FFE000H [PCI] PCI 01FFE000H _pci_map_io: bad request Firmware occupies 0x00010050 ~ 0x00479C60 DATA area is 11276 bytes from 0x001B50A8 to 0x001C00D4 BSS area is 2857864 bytes from 0x001C00D8 to 0x00479C5C Web SDRAM area is from 0X00F00000H [iNIT] HardwareStartup .. [iNIT] MTinitialize .. in usrclk_init() usrclk_init() end 144b50 usrclk_init() 2 end 144b50 System startup... [iNIT] MTmeminit .. [iNIT] check COLOR 0 .. [MEM] main() : COLOR1 free_upnp_memory[1] = 002312F4H soho initialize COLOR1 size : 450000 soho initialize COLOR2 : 50000 [GPIO] reset_adsl_phy() Begin .. IOPDATA1 = 6fffffee [GPIO] reset_adsl_phy() End. Ok! [ADSL] AME F/W is Downloading...Ok! [ADSL] FW Major Version = F3H (D9H) [ADSL] FW Sub Version = B3H (16H) read(0)= 28 read(2)=59904 AMD Am29LV160DB bottom boot 16-bit mode found Set flash memory layout to Boot Parameters found !!! Bootcode version: V1.3d Serial number: SSSSSSSSSSSSSS Hardware version: 01A sizeof(struct III_Config_t) is 57720 read(0)= 28 read(2)=59904 AMD Am29LV160DB bottom boot 16-bit mode found default route: XXX.XXX.XXX.XXX BufferInit: BUF_HDR_SZ=48 BUF_ALIGN_SZ=12 BUFFER_OFFSET=112 BUF_BUFSZ0=384 BUF_BUFSZ1=2176 NUM_OF_B0=0 NUM_OF_B1=1300 BUF_POOL0_SZ=0 BUF_POOL1_SZ=2891200 *BUF0=0x00800200 *BUF1=0x00800210 Altgn *BUF0=0x00800200 *BUF1=0x00800210 End at BUF0:0x00800200, BUF1:0x00ac1fd0 BUF0[0]=0x00800200 BUF1[0]=0x00800210 buffer0 pointer init OK! buffer1 pointer init OK! Interface 0 ip = 127.0.0.1 ssmac_init is called, ifno=1 descritpors tx 256 rx 256 TX_NOCOPY is defined NO_TX_ISR is defined RX_NOCOPY is defined Non-Cache Area : from 00AC21E0H to 00C201E0H Lan channel 0 initialize Function Mac channel 0 initialize Function[sSMAC] BDMA and MAC interrupt vector setup.. [sSMAC] SysSetInterrupt: vector 19 handler 7DB58H [sSMAC] SysSetInterrupt: vector 18 handler 7DB20H [sSMAC] SysSetInterrupt: vector 21 handler 7DB74H [sSMAC] SysSetInterrupt: vector 20 handler 7DB3CH [sSMAC] Set the Initial condition of BDMA, MAC.. [sSMAC] Set the CAM Control register and the MAC address value [sSMAC] Configure the BDMA and MAC control registers .. [sSMAC] Enable interrupt Ethernet interrupt .. [sSMAC] MacInitialize() End. ssmac_init ends Mac addr: MMMMMMMMMMMM MACifno: 1 RUNTASK id=1 rdcemac_intserv_task... Interface 1 ip = 192.168.10.1 [PCI IS FLOW] hwlanPCI_init() Begin .. [PCI 11G] islpci_probe : verdor id 38901260H [PCI 11G] islpci_probe : device id 38901260H [PCI 11G] islpci_probe : revision 2800001H [PCI 11G] islpci_probe : Master Timer 0000H io 01ffe000 irq 00000001 dev_id 00001260 ISL3890 PCI Memory remapped to 0xC1FFE000 PSM Buffer at 0x02AC45E0 size 98304 Queue memory base at 0x00ADC5E0 Queue memory end at 0x00AEE5E0 Unzipping from 80191000 to 00C80000 ... done Uncompressed size = 93996 [HWLAN] set isl_int_mode_flag=1!!! [iSR INIT] HwEnableAllInt(): &INTMASK = F0140008H , INTMASK = 3EFFFFFFH [HWLAN 11G] ifno=2 Card=0 : hwlan_init() [PCI 11G] hwlanPCI_init() set ifp flag .. [HWLAN INIT] hwlan_ioctl() start.. Interface 2 ip = 192.168.10.1 [HWLAN INIT] hwlan_ioctl() start.. InitSAR is called -------------------------------------------------------- SAR Heap Area Information... -------------------------------------------------------- SAR HeapBase : aee5e8 SAR HeapLimit : b0a1e8 SAR HeapSize : 1bc00 --------------------------------------------------------[sAR] Set Interrupt : nSAR_DONE_INT [sSMAC] SysSetInterrupt: vector 16 handler 81D68H [sAR] Set Interrupt : nSAR_ERROR_INT [sSMAC] SysSetInterrupt: vector 17 handler 820F4H SARCFG 00000044 Quesize 256 800000 Quesize 256 800000 Quesize 256 800000 Quesize 256 800000 Quesize 256 800000 Quesize 256 800000 Quesize 256 800000 SAR_GLOBALMODE = c0000000 ChanNum = 0 Request bandwidth: 900000, (e,m)=(11,18), PCR value : 0x5612 [sAR_init] New Channel Number is opened VPI/VCI (8/32) for Interface 3 in writeConnTable : ChanNum 0 PCR 2 = 0x56120000 InitSAR ends CELL_BASE reg = 40000f Ifno= 3 Mac addr: MMMMMMMMMMMM AAL5_PrePare_Hdr: VC=0 AAL5 Enc header len = 8 aaaa0300000008000000 Init NAT data structure I got the gateway[XXX.XXX.XXX.XXX], default route ifno=[3] init_NAT()> default_ifno=3 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 del_virtual_server_by_range> index=0, peer_addr=00000000 iput_IpLinkUp(ifno=3): set ddns_update to 1 Interface 3 ip = XXX.XXX.XXX.XXX ruleCheck()> Group: 0, Error: Useless rule ind[HWLAN 11G] cardmode: 2 [HWLAN 11G] channel: 8 [HWLAN 11G] bsstype: 1 [HWLAN 11G] wep: 1 [HWLAN 11G] authen: 3 [HWLAN 11G] filter: 1 [HWLAN 11G] mode: 143 [HWLAN 11G] ssid: 8 XXXXXXXXXX [HWLAN 11G] psm: 02AC45E0 98304 Intersil firmware version: 1.0.4.3 aLinkState: 0x0, sys_time=0 ex wil[HWLAN 11G] set isl_int_mode_flag=0!!! [GPIO] (_S3C2510) Hwlan_light_init(): TIMER0_INT 23 nTIMER0_INT 29 !! [sSMAC] SysSetInterrupt: vector 29 handler 39A4CH [HWLAN INIT] MAC addr=MM-MM-MM-MM-MM-MM l be truncated ruleCheck()> Group: 1, Error: Useless rule index will be truncated ruleCheck()> Group: 2, Error: Useless rule index will be truncated CBAC rule format check succeed !! reqCBACBuf()> init match pool, Have: 1000 Memory Address: 0x004560d0 ~ 0x0045ce4c reqCBACBuf()> init timeGap pool, Have: 10000 Memory Address: 0x00c4f200 ~ 0x00c7ff54 reqCBACBuf()> init sameHost pool, Have: 2000 Memory Address: 0x0045ce50 ~ 0x0046c870 CBAC rule pool initialized !! sssar_ioctl begin SAR ioctl : opt 1 event 74f31c Init NAT data structure I got the gateway[XXX.XXX.XXX.XXX], default route ifno=[3] RUNTASK id=2 if_task if0... RUNTASK id=3 if_task if1... RUNTASK id=4 if_task if2... RUNTASK id=5 if_task if3... RUNTASK id=6 timer_task... RUNTASK id=7 conn_mgr... RUNTASK id=8 main_8021x... RUNTASK id=9 period_task... [ADSL] Initializing ADSL Modem...® ADSL Modem initialization OK! RUNTASK id=10 adsl_stat_mgr... RUNTASK id=11 dhcp_daemon... httpd: listen at 0.0.0.0:1900 <::::::::::::::::::: CURIOSO HTTPD TIMER_RESOURCE:5, FS_RESOURCE:6 RUNTASK httpd... RUNTASK id=15 dnsproxy... RUNTASK id=16 snmp_task... RUNTASK id=17 dhcpd_mgmt_task... UPnP is disabled Starting Multitask... aMaxFrameBurst: 650 usec aFixedRate: 255 255 255 255 ~[main_8021x] 802.1X authenticator start... RUNTASK id=0 period_task... httpd: listen at 192.168.10.1:80 httpd: listen at 0.0.0.0:8080 <::::::::::::::::::: ??? dnsproxy running... TRAP(coldStart) : send ok! TRAP(linkUp) : 0 send ok! TRAP(linkUp) : 1 send ok! TRAP(linkUp) : 2 send ok! TRAP(linkUp) : 3 send ok! dhcpd_mgmt_task started... deal_packet> msg_type=3, chaddr=MM-MM-MM-MM-MM-MM, idx2=-1 the address is used by the same host adsl_mgr> Idle... Init NAT data structure sssar_ioctl begin ADSL clt call setIPDisconnectEvent()!!! ADSL clt call setPPPDisconnectEvent()!!! setLineSpeed() up:0, down:0 SAR ioctl : opt 5 event 6 [ADSL] Line Closing... Modem Close Rejectd!! C3=00 <::::::::::: mi configuración C4=FC C6=00 C8=00 C9=00 CA=24 NTP_Pooling_Task> before NTP_Query get_ip_by_route> return 0, dst = 15028481 get_ip_by_route> return 0, dst = 292905c0 get_ip_by_route> return 0, dst = ae08bd89 adsl_mgr> ACK/Training... NTP_Pooling_Task> after NTP_Query adsl_mgr> Connected... Unknown response code. [24]Annex-B mode: ITU G.992.1 Annex-B. adsl_mgr> ADSL operation mode: G.DMT adsl_mgr> Interleaved Channel Upstream: 96 <::::::::::: COMO CANTA adsl_mgr> Interleaved Channel Dnstream: 192 <::::::::::: LO MISMO adsl_mgr> Fast Channel Upstream: 0 adsl_mgr> Fast Channel Dnstream: 0 adsl_mgr> Link type is Interleaved Init NAT data structure I got the gateway[XXX.XXX.XXX.XXX], default route ifno=[3] iput_IpLinkUp(ifno=3): set ddns_update to 1 sssar_ioctl begin ADSL clt call setIPConnectEvent !!! ADSL clt call setPPPConnectEvent !!! setLineSpeed() up:96000, down:192000 <::::::::::: ESTA CLARO ¿NO? SAR ioctl : opt 5 event 5 sssar_ioctl begin SAR ioctl : opt 6 event 370f28 ADSL Operationl Mode is Available. NTP_Pooling_Task> before NTP_Query period_task running 60 NTP_Pooling_Task> after NTP_Query period_task running 120 Hasta mañana. Enlace al mensaje Compartir en otros sitios web
Invitado Publicado 6 de Febrero del 2004 Share Publicado 6 de Febrero del 2004 buena informacion esta bien Enlace al mensaje Compartir en otros sitios web
Invitado juanmmr Publicado 6 de Febrero del 2004 Share Publicado 6 de Febrero del 2004 q tema myadsl, podrias indicar algunas de las conclusiones? Asias xD Enlace al mensaje Compartir en otros sitios web
Publicaciones recomendadas