Ir al contenido
Conéctate para seguir esto  
Xurre

Disco de inicio

Publicaciones recomendadas

Hola a todos, estoy intentando actualizar la Bios, para ello necesito un disco de arranque Ms-Dos. He creado el disco de arranque desde el XP profesional. El problema reside en que una vez iniciado el Pc y en la pantalla aparece a:\ no me permite cambiar al disco c:\, invalid parameter

He buscado y lo único que he encontrado en este foro es que utilice un disco de arranque del 98 SE.

este si me permite cambiar a C:\ pero no me sirve tampoco, parece como si leyese un disco C virtual pues los archivos que aparecen no son los que espero tener en este disco.

He bajado alguna que otra utilidad para crear el disquete pero con el mismo resultado, no me deja cambiar al C

Gracias y un saludo

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

Lo mas probables es que el disco C lo tengas formateado como NTFS. Con un disco de arranque msdos no reconocera el disco. Busca en la página web de tu placa base como actualizar la bios. Normalmente lo explican bien..

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

ten en cuenta para q necesitas actualizar la bios

si es por alguna caracteristica necesaria busca en la web del fabricante

si es por te apetece tener la ultima sin mas motivo

ten en cuenta q puede q el rendimiento de la placa empeore

y q si se hace mal o falla algo la placa puede dejar de funcionar

y eso es una manipulacion q no entra en garantia

al igual q la actualizacion del firmware del router

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

Hola a todos, estoy intentando actualizar la Bios para que me reconozca el teclado via usb.

Esta es la placa http://www.msi.com/index.php?func=downl ... rod_no=273

La verdad es que no estoy seguro de cual bajarme, he excogido la version 6380ev51.exe

y estas son las instrucciones:

pecial Note:

The BIOS and DEVICE DRIVERS contained here are exclusively for Micro-Star products only. Micro-Star assumes no responsibility for any damages resulting from improper use or lack of technical expertise.

WARNING!!!!!

DON'T FLASH FROM A FLOPPY DISK!!!!

DON'T FLASH WHEN YOUR SYSTEM IS RUNNING FINE!!!!

DON'T FLASH IF YOU DON'T KNOW WHAT YOU ARE DOING!!!!

Award BIOS Flash Procedure

(Special Thanks to Forum Moderator Bas for his valuable contribution)

1. Check your BIOS for BIOS FLASH DISABLED and ENABLE it, some boards have this function.

For Example:

K7N420 Pro (MS-6373) – BIOS setup/Integrated Peripherals/BIOS Protect/Disabled

2. Know Your model number

a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like K7T Turbo, make sure you have the right version number)

b. Boot up your system & take a look at the top left screen during POST, you should see something like “W6373MS v2.1 122101” This means the board is MS-6373 with BIOS version 2.1

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

3. Download the BIOS that matches your motherboard AND version number (some motherboards are named like K7T Turbo, make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is Intel P4 478 type then look here

http://www.msi.com.tw/support/bios/socket_478.php

if you cannot find the BIOS that matches your board, try here http://www.msi.com.tw/support/bios/more.php

4. Extract the BIOS-archive that you have downloaded by double clicking to c:\test

5. Boot your system from a Win98 or WinME boot-floppy.

How to make boot floppy in case your don’t have it ready:

For Win9X, You can type [C] from the DOS prompt.

For WinMe, You can make a boot floppy from control panel--> add/remove program-->make boot floppy. Remove autoexec.bat & config.sys file if there's any.

For Win2000, there's no way to make boot floppy, so you have to either use Win9X or WinME boot floppy.

For WinXP, you can make a DOS boot disk. Go to Your Computer, right click drive A:, select Format, select copy system files. 

7. When you get the A:\ prompt, type the following sequence:

C:

cd\test

C:\test> awdfl783m BIOS file

(to save or not to save old BIOS is the user’s decision)

8. Reboot your system when prompted

P.S. If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described http://www.msi.com.tw/support/bios/note.htm

AMI BIOS Flash Procedure

(Special Thanks to Forum Moderator Bas for his valuable contribution)

1. Check your BIOS for BIOS FLASH DISABLED and ENABLE it, some boards have this function.

For Example:

K7T266 Pro (MS-6380) –BIOS setup/chipset setup/BIOS protection/disabled

2. Know Your model number

a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like K7T Turbo, make sure you have the right version number)

b. Boot up your system & take a look at the top left screen during POST, you should see something like “A6380MS v1.7 122101” This means the board is MS-6380 with BIOS version 1.7

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

3. Download the BIOS that matches your motherboard AND version number (some motherboards are named like K7T Turbo, make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is Intel P4 478 type then look here

http://www.msi.com.tw/support/bios/socket_478.php

if you cannot find the BIOS that matches your board, try here http://www.msi.com.tw/support/bios/more.php

4. Extract the BIOS-archive that you have downloaded by double clicking to c:\test

5. Boot your system from a Win98 or WinME boot-floppy.

How to make boot floppy in case your don’t have it ready:

For Win9X, You can type [C] from the DOS prompt.

For WinMe, You can make a boot floppy from control panel--> add/remove program-->make boot floppy. Remove autoexec.bat & config.sys file if there's any.

For Win2000, there's no way to make boot floppy, so you have to either use Win9X or WinME boot floppy.

For WinXP, you can make a DOS boot disk. Go to Your Computer, right click drive A:, select Format, select copy system files. 

7. When you get the A:\ prompt, type the following sequence:

C:

cd\test

C:\test> amifl827 BIOS file

(to save or not to save old BIOS is the user’s decision)

8. Reboot your system when prompted

P.S. If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described http://www.msi.com.tw/support/bios/note.htm

Flashing the BIOS for Non-FAT file system (Thanks to Forum Moderator Assaf for his valuable contribution)

1.Check your BIOS for BIOS FLASH DISABLED and ENABLE it, some boards have this function.For Example:

K7T266 Pro (MS-6380) -BIOS setup/chipset setup/BIOS protection/disabled 

 

2.Know Your model number

a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like K7T Turbo, make sure you have the right version number)

b. Boot up your system & take a look at the top left screen during POST, you should see something like "A6380MS v1.7 122101" This means the board is MS-6380 with BIOS version 1.7

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

3.Download the BIOS that matches your motherboard AND version number (some motherboards are named like K7T Turbo, make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is Intel P4 478 type then look here

if you cannot find the BIOS that matches your board, try here

 

4.Extract the file you have downloaded to a floppy (not the win ME/98 startup floppy) by double clocking the file in windows mode and supplying the path a:\

 

5.Boot the computer using a windows ME or windows 98 startup disk. It must be one of these! A plain boot disk will not be good enogh.

If you do not have Windows ME or 98 to create the floppy you can make one on a friend's computer.

 

6.When boot is done there will be a message on the screen showing :"Diagnostic tools were successfully loaded to drive" followed by a single letter.

This letter is the leter assigned to the RAMDRIVE. This RAMDRIVE is a virtual drive in the system memory and can be accessed and controlled like any other drive with DOS commands such as:

MD - Make Directory

Copy - copy a file

Deleate - Deleate a file

 

There is one important difference which is that being in the system memory this drive is wiped once the computer is restarted or shut down.

 

7.Replace the startup floppy with the one containing the flash utility and bios ROM files previously extracted in windows.

 

8.Copy the 2 files to the RAMDRIVE by using the DOS command copy.

Here is an example, in this example the flash utility is AWFL814B.EXE ,the ROM file is  w6373nms.220  and the RAMDRIVE letter assignment is D

 

copy awfl814b.exe d:\

copy w6337nms.220 d:\

 

9.Change the current working directory to the RAMDRIVE root directory, with the example case of the RAMDRIVE being drive D this is done by simply done with the command d:

 

10.Execute the flash utility with the ROM file as a command line argument, with this example:

awfl814b w6373nms.220

 

If you wish to save the current bios you must specify the full path a:\filename. Specifying only a file name will save the bios to the RAMDRIVE which will be wiped after restarting the computer and the file will not be saved.

 

a:\bios.old is an example of the correct way to save the bios.

 

11.Reboot your system when prompted

12. If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described

Gracias por vuestras respuestas :D

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

bien, lo primero dos cosas, ¿tienes instalado el msi live update? este te permitiria actualizar online la bios, si no te tocaria utilizar el programa en ms-dos que te viene en la actualizacion de la bios

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

hola, si pero con problemas. Tanto por Live Update online como el programa instalado me sale la pantalla azul con este mensaje:

"Se ha encontrado problemas y...........apagado para evitar problemas............originado en este archivo msibios32 1000507.sys PAGE FAULT IN NONPAGED AREA.

Compruebe hadware o software está correctamente instalado ...si persiste desactive las opciones de memoria de la bios como cache o vigilancia

STOP 0X000000050 (0XB16FD000,0X00000000,0XB192B929,0X00000000)

msibios32 100507.sys

ADRESS B192B929,B192A000,4be3dbcd"

Un saludo :D

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web

¿has probado a pasarle un antivirus/antispyware? hazle un disquete de arranque con la opcion crear disco de ms-dos, copiale los archivos al disquete e inicia desde el disquete, luego sigue las instrucciones del programa

Compartir este mensaje


Enlace al mensaje
Compartir en otros sitios web
Invitado
Este tema está cerrado a nuevas respuestas.
Conéctate para seguir esto  

×
×
  • Crear nuevo...

Información importante

Términos de Uso Política de privacidad Hemos colocado cookies en su dispositivo para ayudar a mejorar este sitio web. Puedes ajustar la configuración de tus cookies ; de lo contrario, asumiremos que quieres continuar.